Notice: The following answers to frequently asked questions, are meant to be a reference when seeking the services of a certified A/C Service Technician, and are not to be used as a guide or endorsement for servicing your own A/C system.

Frequently Asked Questions:

1. Why do I need to use an exact amount of Freon?

2. What is a "Liquid Charge", and why is it dangerous?

3. What causes clutch failure?

4. What causes compressor failure?

5. Why should I use R134a refrigerant?

6. What does humidity have to do with my air conditioner?

7. Where does the "High Side" begin?

8. Just what is this "Black Death"?

9. What exactly does a drier dry?

10. What is your position on flushing?

11. What about system leaks?

12. What does all this A/C jargon mean?

13. What is a ton of refrigeration?

14. How many different condensers are there, and which can be flushed?

15. What causes excessive clutch cycling?

16. Why should I worry about ESD?

17. Can compressors take all that heat?

18. Does it matter what oil I use?

19. What are the "Three laws of air conditioning"?

20. What should be done when installing a compressor?

21. How does an automotive A/C system work?

22. What about "Low Air flow"?

23. My clutch (or switch) does not function, what can I do?

24. Is a little moisture in the system really such a big deal?

25. What are the basic A/C systems?

26. How are clutch cycling switches different?

27. Are your compressors compatible with R12 or R134a?

28. Do your compressors come with a clutch? I don't see any mention of the clutch on the details page.

29. Is there a core charge? If so, how much?

30. How long is the warranty on your compressors?

Why do I need to use and exact amount of Freon? Today's A/C systems use smaller amounts of Freon. No longer is it 2 to 4 lbs, but rather 18 to 38 oz. With tight compressor tolerances and lubricant mixed with the Freon, the mixture must be just right to enter the compressor as a mist. Wrong mixtures will either under lubricate or slug the compressor causing premature failures. You don't know how much liquid Freon is in a system so you should recover the old Freon, evacuate and add the correct charge. Always check the OEM spec for the correct charge. Back to the Top

What is a "Liquid Charge", and why is it dangerous? A "Liquid Charge" is any charging of the A/C system using Freon which enters the A/C system in a liquid state as opposed to a gaseous or Vapor state. Warning! Charge A/C System with Freon as Vapor, not Liquid! If a charging hose is long enough you might get away with using liquid refrigerant because the liquid will partially change to a gas in the hose. The odds are not in your favor. More often you will freeze and shatter the compressors valves when the refrigerant hits the valves as a liquid. This happens in mere seconds, which is why we recommend charging the A/C system with the engine off. Back to the Top

What causes clutch failure? Some common causes for clutch failure: 1. Bearing failure. 2. Air Gap: Between the outer plate (hub) and the belt/rotor (.016 -. 030 inch) Note! Air gap varies with compressor type - check OEM specs. 3. Shorted Coil - Due to improper polarity or weak/burnt winding. 4. Low voltage at coil will cause coil to overheat due to slippage. 5. Locked Compressor: Excessive discharge pressure - Check for restricted condensers, receiver/driers or an oil over charge 6. Belt is wrong type, wrong size, miss-aligned or loose. Back to the Top

What causes compressor failure? Some common causes for compressor failures are: LACK OF USE: Compressors not run regularly will be starved for lubrication when they are turned on. This causes excessive ware until the oil again reaches the compressor. It's best to use the A/C once a week for a few minutes. FAILURE TO FLUSH SYSTEM: Compressors and hoses wear causing bits and pieces to mix with the oil. This sludge gets into the compressor and can cause it to seize. Failure to properly flush or using flush that leaves a residue is a primary cause of failure. EXCESSIVE HIGH OR LOW PRESSURE: Condenser fans can quit due to bad connections or defective motor windings that get too hot. This creates excessive head pressure and heat that can lock up or damage a compressor. Loose connections at the coil can cause high resistance and low voltage causing clutch slippage. Low refrigerant charge will cause lack of lubrication getting to the compressor. Painting condensers will insulate them from efficiently removing heat and increase head pressure in the compressor. IMPROPER FREON OR OIL CHARGE: Compressors manufactured after 1990 have smaller capacity, therefore use less refrigerant and oil and are extremely sensitive to inadequate amounts of oil. The wrong type of oil may break down in high heat conditions. R134a systems are more sensitive to lubrication than R12 systems. An over charge of oil can clog the condenser, the orifice tube or expansion valve and starve the compressor of oil. R12 systems use mineral oil and R134a systems use PAG or Double End Capped PAG Oil (always check the OEM specs) REFRIGERANT BLENDS They can affect seals and O-rings, causing them to leak, swell or otherwise deteriorate and it can happen relatively quick. Back to the Top

Why should I use R134a refrigerant? R12 has the ozone depleting chemical chlorine in it and has been replaced with a refrigerant known as R134a. A boiling fluid absorbs heat and changes its state to a vapor. The expanding vapor/gas has a lower pressure than the liquid and therefore lower temperature. For heated air to be absorbed it must transfer to a cooler surface. The trick is to find a liquid that boils at such a low temperature that the vapor is cold enough to absorb the amount of heat generated inside an automobile. Freon-12 boils at -22º F and its expanding vapor, in the evaporator core, absorbs the heated air circulating around it. Freon-134a boils at about the same temperature as R12 and therefore is a good replacement. Back to the Top

What does humidity have to do with my air conditioner? You're A/C unit works to remove heat from the passenger area and in doing so it also removes moisture. We are most comfortable when the relative humidity is closer to 20 percent than 90 percent, therefore the A/C system expends most of its effort wringing moister out of the air. This is what air conditioning is all about - conditioning the air. It's important to check the condensation drain at the bottom of the evaporator. If you see clear water dripping from your car, when parked… it's a good thing…if it's from the evaporator. Back to the Top

Where does the "High Side" begin? Where ever the dam is located is the separation point. We call it a dam because it has high pressure on one side and low pressure on the other. This separator is call an Expansion Valve or an Orifice Tube. Its job is to allow only enough refrigerant through to allow gas expansion in the evaporator. By limiting the flow of gas it creates the high pressure back to the compressor. Back to the Top

Just what is this "Black Death"? Black Death, as it is known by A/C techs, is a result from the breakdown of the refrigerant-lubricant. This causes excessive wear inside the compressor and the excessive ware causes a black residue that is actually a combination of solder flux from the condenser and aluminum shavings from the old compressor. When this goop cools, it hardens in the condenser. Repeated flushing will not remove it, however, when the system is charged and running it liquefies, flows out into the liquid line and clogs the orifice tube. With less refrigerant flowing, past the orifice tube, the compressor is starved of lubricant and will lock up. The only answer is to replace the condenser. Back to the Top

What exactly does a Drier dry? It's not the freon!! It's the oil in the refrigerant that absorbs moisture and holds debris in the system. Replacing the drier or accumulator, in addition to evacuation, will assure better performance. Back to the Top

What is your position on flushing? Oil, sludge and debris that is left in the system can clog the condenser, orifice tube or expansion valve and damage the compressor. Flushing can remove excess oil and debris from previous services. You do not want to add yet another charge of oil while leaving an unknown amounts of oil in the system. Caution! Only flush a condenser that capable of being flushed. The answer to question #14 deals with this problem in greater detail. Back to the Top

What about system leaks? At one time Freon was cheap and a 2oz. per year leak was acceptable in a 4-5 lb. System. Today systems are smaller and 1/2oz makes a big difference in performance. Good halogen leak detectors will show most system leaks, under static conditions, however some will leak only when the system is in operation. This is where the insertion of a florescent dye can help find the leak. Note, to see the dye stain you need a UV lamp and the leak has to be where the light can reach it. Most car manufactures approve the use of trace dyes and some OEM's have been inserting trace dyes on the assembly line. Dye can be inserted either when charging or when the system is charged. The amount of dye used is less than 1/3 oz and remains in the system even if the total charge is lost. The dye stains the oil not the Freon and only flushing will remove it. Back to the Top

What does all this A/C jargon mean? Glossary of Terms: ACCUMULATOR: stores & filters Freon (on Low side of system) BTU: British thermal unit AMBIENT AIR: outside air CAPILLARY TUBE: gas filled temperature-sensing tube CCOT: clutch cycling orifice tube that replaces the TXV CLUTCH CYCLE SWITCH: evaporator temp controlled switch that cycles clutch COMPRESSOR: pump that moves the refrigerant. CONDENSER: heat exchanger-removes heat from refrig DISCHARGE LINE: compressor outlet line DRIER: filters refrigerant (located on High side of system) EPA: Environmental Protection Agency ESD: Electrostatic Discharge EVAPORATOR: heat exchanger-removes heat from air HEAT: anything above absolute zero has heat HEAT EXCHANGER: device for transferring heat LIQUID LINE: moves high-pressure liquid through system MANIFOLD: connects suction & discharge lines to compressor PAG: Polyalkylene glycol (lub used with R134a refrigerant) PROM: Programmable Read Only Memory - use in computers SUCTION LINE: between evaporator outlet and compressor TXV: Thermostatic Expansion Valve - maintains evaporator   Back to the Top

What is a ton of refrigeration? One Ton of refrigeration is defined as amount of heat (288000 Btu's) required to cause a change in state of one ton of ice to one ton of water at 32 degs. F in 24 hours. A/C units are rated by Btu/hour ratings. A one ton unit is rated as 12000 Btu's (288000/24) The average factory installed auto A/C unit is rated at 1-3/4 ton. Back to the Top

How many different condensers are there, and which can be flushed? R134a condensers have more fins/inch than R12 condensers and their fin diameters are smaller.( 6mm) TUBE and FIN - Oldest industry standard, 3/8-inch diameter round tube condenser. Ok, for R12 but not recommended for R134a. This type of condenser is flushable. 6 mm PICCOLO multi-flow: smaller, lightweight and more efficient than 3/8-inch tube and fin and serpentine. Used in many domestic OE applications. This type of condenser is flushable. SERPENTINE: All aluminum, more efficient than tube and fin, used on smaller imports where space is limited. This type of condenser is not easily flushed, replacement is recommended. PARALLEL FLOW: all aluminum, this efficient design breaks up flow into tiny streams that give up heat more rapidly. This type of condenser is not flushable, replacement only! PARALLEL FLOW with SUB Condenser. Oval tube multi-flow and sub-condenser stacked up. Refrigerant flows through the multi-flow into the drier (called a modulator) then continues as a liquid into the sub-condenser. This type of condenser is not flushable, replacement only! Back to the Top

What causes excessive clutch cycling? It's common to assume low refrigerant is the cause for excessive clutch cycling and this often leads to adding refrigerant and thereby overcharging the system. Most vehicles have a compressor clutch cutout strategy based on an engine coolant temperature of 220 - 240 degs F. The vehicles computer relies on a coolant temperature sensor to provide the signal for the compressor clutch decision and if the sensor reads too high the clutch will cycle off. Cooling systems with a 50-50 anti-freeze mix and the proper radiator cap should boil at around 275 degs, so the system may not be boiling when the compressor cuts out. Check the actual coolant mix and temperature by using an Infrared thermometer to check coolant temperature and a Scan Tester to tell you what temperature the sensor is actually signaling to the computer. Back to the Top

Why should I worry about ESD? During the testing and repair of computer controlled vehicles we come in contact with components that may be damaged by ESD or static electricity. When installing new electronic components, the part itself may have developed a charge from contact with the package during handling; therefore you need to ground yourself to the body ground of the vehicle. This is easily done by using a wrist strap that is available at most electronic supply stores (Radio Shack) Back to the Top

Can compressors take all that heat? A compressor can take the heat, but if there's a condenser airflow problem, overcharge, poor lubrication, restriction, etc., the temperature can greatly rise and cause the compressor to seize. Some vehicles have compressors mounted low in the engine compartment and due to poor airflow the compressor can overheat and fail. Back to the Top

Does it matter what oil I use? The moving parts of a compressor must be lubricated during operation. The oil is absorbed into the refrigerant that carries it through the compressor as a mist. An oil over/under charge can damage the compressor. Compatibility of refrigerant oil is determined by its ability to remain oil when mixed with the refrigerant and not become separated by a chemical reaction. R12 systems use a non-foaming sulfur-free grade of mineral oil (YN-9) formulated for that refrigerant and cannot be used in R134a systems. R134a systems use either synthetic oil (PAG) YN-12 or Double End Capped PAG oil. Back to the Top

What are the "Three laws of Air Conditioning"? Everything has heat except at absolute zero (-460 degs. F) LAW I: to refrigerate is to remove heat - the absence of heat is cold. LAW II: heat is ready to pass to anything that has less heat - nothing can stop the flow, you can only slow it down LAW III: if a change of state is to take place there must be a transfer of heat - If a liquid is to change to a gas it must take on heat. Back to the Top

What should be done when installing a compressor? Flush, with an approved solvent, to Clean the system* Replace the Accumulator/Drier or Orifice tube Replace manifold sealing washers or O-rings Use a Vacuum Pump (20+ minutes) to remove moisture. Add the proper amount and type of oil. Check OEM spec Rotate compressor hub 12 times to oil the shaft seal Place a strong external airflow into the condenser Check OEM specifications for correct refrigerant charge Charge with VAPOR refrigerant and with A/C and engine off. Do a leak test and check voltage at clutch coil Check belt tension and alignment Check system operation at 1500 RPM and mid-blower speed Use gauges to check the system pressures. *Only if the condenser is the type that can be flushed. Back to the Top

How does an automotive A/C system work? All matter has a certain amount of heat except at absolute zero (-460º F). Ice cubes feel cool to the touch, but actually it just has less heat than your hand. Heat is transferring from your hand to the ice cube. This is the principle behind how an A/C cools the air in a car. Heated air is circulated across a gas filled evaporator and is transferred to the refrigerant gas making the air less hot. The heat-laden refrigerant then is drawn into the compressor, is super heated by compression and forced through the condenser where the cooler outside air takes the heat from the refrigerant. Its next stop is the expansion device (TXV or Orifice tube), which meters refrigerant into the evaporator where it expands into a gas and it starts over again. Back to the Top

What about "Low Air Flow"? The complaint: "it used to blow harder". Things to check are: Low blower motor voltage due to a poor ground Blower wheel loose on motor shaft Defective blower relay Air leak or obstruction in air duct system Air mode door directing some of the flow to the heater outlet Icing evaporator core due to condensation. Debris in evaporator housing that blocks air circulation. Obstruction at the air return Back to the Top

My clutch (or switch) does not function, what can I do? Electronic circuits are sensitive to voltage drops and operate in narrow voltage ranges. Many connectors have small spade or pin type connections and are engineered to have near zero resistance. If the connection is even slightly loose it will affect the voltage. What may seem to be a defective component could be a bad connector. The problem may be corrosion and careful brushing or using an electrical contact cleaner may cure it. Many OEM harness connectors are available as replacement parts. Back to the Top

Is a little moisture in the system really such a big deal? Moisture causes internal icing that obstructs the orifice tube or expansion valve. This can create excessive high pressures and low cooling. The A/C system is a closed loop system so why does it need a Drier to remove moisture? Here's how moisture gets into the system. Refrigerant charged through service hoses not evacuated after being connected to the system will have air and moisture in them. Hoses left uncapped while replacing components allows moisture to enter. Refrigerant oil is hydroscopic (water absorbing like a sponge) and left uncapped will have moisture in it. Recycling machines with old filters will not remove moisture from incoming refrigerant. Condensation created when the Low side of the system gets cold and then warms up when the system is turned off is absorbed into the system through the hoses. Systems low on freon will pull moisture into the system when they go into a partial vacuum. Back to the Top

What are the basic A/C systems? ORIFICE TUBE SYSTEM Orifice tube systems use an Accumulator located in the Low side of the system EXPANSION VALVE SYSTEM TXV systems use a Drier located in the High side of the system. Back to the Top

How are clutch cycling switches different? The clutch cycling switch for R134a vehicles has been calibrated for the slightly higher pressure of R134a. The threads, on the switch fitting, have been changed to metric to avoid connecting to a R12 system. Back to the Top

Are your compressors compatible with R12 or R134a refrigerant? All of our compressors are remanufactured with retrofitting in mind. Each compressor is remanufactured with Nitrile or HNBR seals which allow the compressor to be installed in either R12 or R134a refrigerant systems. Back to the Top

Do your compressors come with a clutch? All of our compressors come complete with the clutch assembly. No compressor leaves our facility without the clutch assembly attached and fully tested. Back to the Top

Is there a core charge? If so, how much? As the compressor market is so volatile, we do not charge a core charge. This allows us to further pass the savings to our customers. The price you see on the website is the outright price (+ Shipping & or Tax). In the event you purchase one of the harder to find units, we will send a prepaid UPS return tag with the compressor. If your old unit is in rebuild-able condition, we will issue a credit back to your method of purchase based on market value at the time. Back to the Top

How long is the warranty on your compressors? The short answer: 12 Months. However, the actual term of the warranty varies depending on the units application. (i.e., Heavy Duty application compressors are only warranted for a period of 6 months). Please refer to our Warranty Policy (Button on the left) for further details. Back to the Top